Yamaha Yz 125 Manual

Yamaha YZ125 YZ 125 Manual

Turning in the pilot air screw will enrich the mix- ture at low speeds, and turning out it will lean out the mixture. Apply the brake fluid on the master cylinder cup.

To dispose of a damaged or worn-out shock absorber, van valkenburg network analysis take the unit to your Yamaha dealer for this disposal procedure. We recommend to use Yamaha genuine parts for all replacements.

Yamaha YZ Owners Manuals

Install the cap with its mark a facing forward. Air filter element Damage Replace. Elevate the front wheel by placing a suitable stand under the engine.

Never attempt to pry out piston seals and dust seals. Install the reed valve spacer with its wider con- tact surface side a to the right.

Note the position of each part. Install the bearing in the bearing races.

Yamaha YZ125 Manuals

Compress the front fork fully. If you make a mistake in the grip cap installation position, the brake lever may contact the grip cap, resulting in poor brake performance. Leave a Reply Cancel reply Your email address will not be published.

Yamaha YZ YZ ManualYamaha YZ125 Manuals

Amazon Music Stream millions of songs. In this revised format, the condition of a faulty component will precede an arrow symbol and the course of action required will follow the symbol, e. Hold the impeller shaft on its width across the flats a with spanners, etc. If the mixture is too rich or too lean at intermediate speed operation, irregular engine operation and poor acceleration will result. Vers la fente de tube externe.

Apply the molybdenum disulfide grease on the bushes, thrust bearings and oil seal lips. Take care not to scratch the inner tube. Do not use a hammer to drive out the crankshaft. This is an awesome site, very helpful. Before washing the machine, block off the end of the exhaust pipe to prevent water from entering.

Yamaha YZ Owners Manuals

The bending value is shown by one half of the dial gauge reading. Tighten the nut while applying the rear brake. The ad- juster may be damaged. Connect and disconnect the connector two or three times.

Yamaha YZ125 Manuals

Below you will find free PDF files for your Yamaha YZ owners manuals

Any reprinting or unauthorized use without the written permission of Yamaha Motor Co. Le specifiche relative alla coppia per componenti o gruppi speciali sono incluse nelle se- zioni pertinenti di questo manuale. If there is any question you have regarding this manual or your machine, please consult your Yamaha dealer. If your machine is stolen, the authorities will need the number to search for and identify your machine. Use of soft spring Generally a soft spring gives a soft riding feeling.

If other oils are used, they may have an ex- cessively adverse effect on the front fork performance. This is the position which is back by the spe- cific number of clicks from the fully turned-in position. If torqued too much, it may cause the front fork to malfunction. Wash the all parts in a clean solvent.

The brake pedal height is the vertical distance from the inside top end of the footrest. Ammortizzatore Posteriore Anweisungen beachten. Apply the transmission oil on the spacer, bearing and primary driven gear inner circumference.

When installing the flywheel puller, turn it coun- terclockwise. Stiffer a a Increase the high compression damping force. Therefore, carburetor setting requires the change of the jet needle. Elevate the rear wheel by placing the suit- able stand under the engine.

Apply the lithium soap base grease on the wheel axle. Does it get rusted whenever you take it to the car wash? Use a thin screw driver, and be careful not to damage the inner fork tube and dust seal. The front fork requires careful attention. Thank you for your feedback.

All circlips should be inspected carefully be- fore reassembly. Install the bearing by pressing its outer race. Therefore, be sure to make re-evaluation. Do not use a sharp instrument.

The coolant is harmful so it should be handled with special care. Apply water on the radiator cap seal.

Tighten the nuts in stage, using a crisscross pat- tern. Install the brake hose so that its pipe por- tion a a directs as shown and lightly touch- es the projection b b on the master cylinder. Lavare i cuscinetti e le piste con de roulement dans du solvant einem Reinigungsmittel un solvente. Perform the pre-operation checks on the machine.

Apply the lithium soap base grease on the throt- tle cable end and tube guide cable winding por- tion. Page Unsmooth operation Repair. Turn the torsion spring clockwise and hook into the proper hole a in the crankcase. Fully finger tighten the locknut onto the damper assembly.

Page Anweisungen beachten. Your email address will not be published. Always use fresh, name-brand gasoline, and mix the oil and gas the day of the race. Do not apply the grease on the bearing outer race because it will wear the rear shock absorber surface on which the bear- ing is press fitted.